bending strain

And the influence of bending strain on critical currents and measured losses were analyzed.

分析了弯曲应变对它们的影响。

互联网摘选

Measurement and Analysis of Dynamic Bending Strain in Marine Shafting

船舶轴系动态弯曲应变的测量与分析

互联网摘选

The results made clear that the widely used method with attached stiffness set in compressive test of stress-strain complete curve was not proper for concrete in direct tension. complete curve of a three-point bending concrete beam is realized.

在普通试验机上进行的混凝土抗拉应力-应变全曲线的试验研究结果表明，在抗压全曲线试验中采用的刚性试验机和附加刚性组件的方法在抗拉全曲线的试验中并不适用。

互联网摘选

The FA reducer pin teeth structure is lying pillow type, so the bending strain may be ignored.

由于FA型减速器针齿采用卧枕式结构，弯曲变形可不计。

互联网摘选

Study on strain concentration area for SB type bending beam sensor

SB型弯曲梁式传感器应变集中区探究

互联网摘选

Experimental study on limit tensile strain under bending of compacted soil

几种击实土挠曲极限拉应变的试验研究

互联网摘选

The methods of compressing strain energy and bending strain energy are adopted to study low temperature performance of montmorillonite modified asphalt with two different montmorillonites by indoo.

通过两种武汉市售蒙脱土和实验室纯化蒙脱土，采用压缩应变能、弯曲应变能的方法，进行蒙脱土改性沥青低温性能研究。

互联网摘选

In this thesis, the combined theory of strength and stability is discussed from the derived proportional law-stress-strain relation and the balance state of beam complex bending-the basis of the combined theory of strength and stability.

本文从应力应变关系衍生比例定律到强度稳定综合理论的基础梁柱复杂弯曲的平衡状态，将强度稳定综合理论在原有的基础上从新总结论述。

互联网摘选

Series solutions were derived for the in-plane strain, deflection and bending strain that satisfy the simplified boundary conditions to calculate the shear lag coefficient.

根据简化的边界条件，得到了面内应变和弯曲应变的级数解，进而求得剪力滞后系数。

互联网摘选

This thesis establishes the mathematical models of measuring angle strain and bending strain, develops the functional relation between the strain and the measuring values.

建立了电磁检测法检测构件弯曲正应变和剪应变的数学模型，推导出应变与时间域计测值之间的函数关系；

互联网摘选

According to the deformation of shear spinning on conical workpieces, the stress and strain has been analyzed and the new deformation mechanism has been put forward that the forming area of shear spinning should be divided into tension bending zone and rolling zone.

根据剪旋过程的实际情况进行了应力应变分析，对剪旋变形机理提出了新的见解，将剪旋变形区分为拉弯区和辗压变形区。

互联网摘选

The pivotal dynamic indexes such as tip error, joint torque and bending strain previous works.

分析计算了机械臂末端误差 、 关节扭矩、弯曲应变等主要的动力学指标.

互联网摘选

Beam bending test of RPM pipe and control of beam bending strain in construction

RPM管梁弯曲试验及其梁弯曲应变的工程控制

互联网摘选

Determination of the long-term ultimate bending strain and calculation of the long-term ultimate relative ring deflection, both under wet conditions

潮湿条件下长期环状弯曲应变和长期环形偏转的极限测定

互联网摘选